Warnings, error and information messages

The exception messages of SilverStar Sewing Control System is divided into three groups, as shown in the following table:

Level	Code	Description
Error	Err	Switch off the control and eliminate the problem
Warning	Wrn	Eliminate the state that caused to the warning, the control will normally worked
Information	Inf	Work can be continued, only exception message needs to be confirmed

Exception quick reference

Error messages

Code	Messages	Remedial action
ExcCode101	ac power excess voltage	ExcCode101.solution()
ExcCode103	bus excess voltage	ExcCode103.solution()
ExcCode106	motor excess current	ExcCode106.solution()
ExcCode107	overload/motor speed too low	ExcCode107.solution()
ExcCode108	motor excess phase current	ExcCode108.solution()
ExcCode109	motor blocked when start	ExcCode109.solution()
ExcCode110	motor blocked	ExcCode110.solution()
ExcCode111	motor uvw signal	ExcCode111.solution()
ExcCode112	motor encoder error	ExcCode112.solution()
ExcCode113	magnet/solenoid over-current	ExcCode113.solution()
ExcCode114	motor encoder error	ExcCode114.solution()
ExcCode126	panel connection error	ExcCode126.solution()
ExcCode127	panel connection lost	ExcCode127.solution()
ExcCode128	data checksum error	ExcCode128.solution()
ExcCode129	stepper connection error	ExcCode129.solution()
ExcCode130	data checksum error	ExcCode130.solution()
ExcCode191	Controller: upgrade	ExcCode191.solution()
ExcCode192	Controller: upgrade	ExcCode192.solution()
ExcCode193	Controller: upgrade	ExcCode193.solution()
ExcCode194	Controller: upgrade	ExcCode194.solution()
ExcCode195	Controller: upgrade	ExcCode195.solution()
ExcCode196	Controller: upgrade	ExcCode196.solution()
ExcCode197	Controller: upgrade	ExcCode197.solution()
ExcCode198	Controller: upgrade	ExcCode198.solution()
ExcCode199	Controller: upgrade	ExcCode199.solution()
ExcCode181	HMI: upgrade	ExcCode181.solution()
ExcCode182	HMI: upgrade	ExcCode182.solution()
ExcCode183	HMI: upgrade	ExcCode183.solution()
ExcCode184	HMI: upgrade	ExcCode184.solution()
ExcCode185	HMI: upgrade	ExcCode185.solution()
ExcCode186	HMI: upgrade	ExcCode186.solution()
ExcCode187	HMI: upgrade	ExcCode187.solution()
ExcCode188	HMI: upgrade	ExcCode188.solution()
ExcCode189	HMI: upgrade	ExcCode189.solution()

Warning messages

The code of the warning message is always less than 100.

Code	Messages	Remedial action
ExcCode1	pedal	ExcCode1.solution()
ExcCode2	tilt switch	ExcCode2.solution()
ExcCode3	shortkeys	ExcCode3.solution()
ExcCode4	shortkeys	ExcCode4.solution()
ExcCode5	bobbin counter/monitor	ExcCode5.solution()
ExcCode6	upper thread breaking	ExcCode6.solution()
ExcCode7	service counter	ExcCode7.solution()
ExcCode8	eye protection	ExcCode8.solution()
ExcCode9	slide monitoring	ExcCode9.solution()

Information messages

The code of the information message is always less than 100.

Code	Messages	Remedial action
ExcCode50	oil level	ExcCode50.solution()

Error message list

exception ExcCode101

AC power supply voltage is too high

solution()

Check the ac voltage; Replace the controller.

exception ExcCode103

Bus voltage is too high

solution()

Check the brake circuit, replace the brake resistor; Replace the controller.

exception ExcCode106

The bus current is too high

solution()

Check the motor encoder connection; Check if the right MACHINE ID is seted; Replace the controller;

exception ExcCode107

Overload, the speed of main motor is too low

solution()

The shaft is blocked; The material is too thick.

exception ExcCode108

Overload, the current command of main motor exceeds the maximum value

solution()

The shaft is blocked; The material is too thick.

exception ExcCode109

The main motor starts failed

solution()

Restart the machine from where the sewing material is thinner; The shaft is blocked; The material is too thick.

exception ExcCode110

The synchronizer signal is not detected

solution()

Check the synchronizaer signal; The shaft is blocked; The material is too thick.

exception ExcCode111

Motor UVW signal is abnormal

solution()

Check the UVW signal; Replace motor encoder

exception ExcCode112

The motor synchronization signal cannot be detected for a long time after press the pedal.

solution()

Check the synchronizaer signal; Replace motor encoder.

exception ExcCode113

The solenoid current is too high

solution()

Check the solenoid; Replace the controller or solenoid;

exception ExcCode114

Abnormal value of motor angle

solution()

Check the motor encoder connection; Check the hall sensor;

exception ExcCode126

The paramter synchronization is failed

solution()

Check the panel connection; Restart the control box

exception ExcCode127

The panel is reconnected when some special mode

solution()

Restart the controlbox

exception ExcCode128

Parameters verified failed

solution()

Restart the controlbox; Update software.

exception ExcCode129

The step drive communication failed

solution()

Restart the controlbox; Check the communication cable.

exception ExcCode130

Parameters version verified failed

solution()

Update the software of controlbox or panel.

exception ExcCode191

Controller upgrade files data error: wrong file

solution()

Update software

exception ExcCode192

Controller upgrade files data error: wrong page

solution()

Copy the upgrade files and update again

exception ExcCode193

Controller upgrade files data error: verification failed

solution()

Copy the upgrade files and update again

exception ExcCode194

Controller upgrade files data error: wrong size

solution()

Copy the upgrade files and update again

exception ExcCode195

Controller upgrade files data error: start address

solution()

Copy the upgrade files and update again

exception ExcCode196

Controller upgrade files data error: model not match

solution()

Copy the upgrade files and update again

exception ExcCode197

Controller upgrade files not exist

solution()

Copy the upgrade files and update again

exception ExcCode198

Communication timeout when upgrade the controller

solution()

check wire connection and update again

exception ExcCode199

No USB drive detected

solution()

Reinsert the USB disk and update again

exception ExcCode181

Wrong panel software

solution()

Update software

exception ExcCode182

Panel upgrade files data error: wrong page

solution()

Copy the upgrade files and update again

exception ExcCode183

Panel upgrade files data error: verification failed

solution()

Copy the upgrade files and update again

exception ExcCode184

Panel upgrade files data error: wrong size

solution()

Copy the upgrade files and update again

exception ExcCode185

Panel upgrade files data error: wrong start address

solution()

Copy the upgrade files and update again

exception ExcCode186

Panel upgrade files data error: model not match

solution()

Copy the upgrade files and update again

exception ExcCode187

Panel upgrade files not exist

solution()

Copy the upgrade files and update again

exception ExcCode188

Communication timeout when upgrade the panel

solution()

check wire connection and update again

exception ExcCode189

No USB drive detected

solution()

Copy the upgrade files and update again

Warning message list

exception ExcCode1

Pedal warning

solution()

The pedal must be released when switching on; The pedal type must be set correctly when using standing pedal; Replace the pedal.

exception ExcCode2

Tilt switch warning

solution()

The warning will be cleared when the machine is back to the normal position; Check the tipping sensor on the machine

exception ExcCode3

Shortkey warning

solution()

The short key must be released when switching on

exception ExcCode4

Shortkey warning

solution()

The short key must be released when switching on

exception ExcCode5

Bobbin counter warning

solution()

Replace the bobbin, press back key to clear warning

exception ExcCode6

Upper thread breaking warning

solution()

The upper thread is broken; Check the sensor of upper thread.

exception ExcCode7

Service counter warning

solution()

Make a service maintenance, press back key to clear warning

exception ExcCode8

Eye protection monitoring

solution()

Put eye protection cover plate back in place; Check the sensor of eye protection.

exception ExcCode9

Slide monitoring

solution()

Close the hook cover plate; Check the sensor of slide monitoring;

Information message list

exception ExcCode50

Oil level is below the minimum level marking

solution()

Maintenance necessary, see the service instructions for the machine to lubricating the machine

Changed in version 90A0-v1.08.05: Previously, the code of this exception was 10 and belonged to warning group.